+ Plastic
+ Foam
+ Hard Wood, soft woods
+ Circuit Board
+ Light Aluminum
+ Brass
+ Jewelry wax
+ Corian
+ Carbon Fiber

• Structure is CNC machined 6061 aluminum and extrusions
• 6061 Billet Machined Aluminum
• Standard X and Y Axis uses 20mm ABBA Brand linear rails/blocks (4 Blocks for X and 2 for Y)
• Upgrade only X and Y Axis uses 20mm THK Brand linear rails/blocks (4 Blocks for X and 2 for Y). Must be stated in the formal Quote.

• Ratio is 2:1 on X, Y and Z.
• Pulley made of Aluminum.
• Belt is reinforces fiber.

• Up and down motion.
• Linear Hardened Shaft Guides
• Linear Bearings Blocks with grease inlet.
• Rolled Ballscrews .001" Backlash.
• Resolution .0001"
• Recirculating ball nut with grease inlet.
• Belt Drive geared down for power and accuracy.
• 5" Travel
• Standard X and Y Axis uses 20mm ABBA Brand linear rails/blocks
• Upgrade only X and Y Axis uses 20mm THK Brand linear rails/blocks. Must be stated in the formal Quote. Now available 5/4/2006
• Colombo spindles require upgrades to include additional blocks and longer rails on Y Axis (24" travel axis). and the Z axis. Now available 5/4/2006

• Rolled Ballscrews of .001" backlash tolerance.
• Resolution .0001"
• Precision rolled hardened.
• Recirculating ball bearing Ball Nut.
• Made of steel.
• Standard ABBA rails and ballscrews.
• Upgrade at an additional price - Z Axis uses 20mm THK Brand linear rails/blocks. Must be stated in the formal Quote.

Machine Travel center of bit: + Travel: X=39" Y=25" Z=5"

Clearance of part with 5inch Z: + X=24" (side column clearance). + Y=40"or longer (table supports 30"). + Z=5" table top to Z bottom. + Z=5.75" No table to Z bottom.

Dimensions of machine: + Machine bottom X=31" Y=49" Z=24.5"

Enclosure Dimensions, Estimate only: + X=37" (side column clearance). + Y=54". + Z=46 for 5" Z. We recommend you build the enclosure after you receive the machine.

• Parallel Printer Cable for controls (Currently No USB)
• USB for additional 5W Power Only
• Power Cord for 110 VAC
• International Power Cord for 220 VAC (Please request)

• Comes Standard.
• Used for Homing, Zeroing X, Y and Z.
• Pre-Wired
• Adjustable on X and Y
• Requires the purchase of Controller with limit switch option
• Made of micro switches

• Comes Standard.
• Most Accurate Cutting Z-Axis
• Heavy load
• Sealed
• High rigidity
• Low axis motion noise
• High durability
• Low maintenance

• Porter Cable 892 - 2.25HP - NEW Tool Changing easier than Hitachi (Single Tool Changer)
• Porter Cable 7518 - 3.25HP
• NEW* Bosch - 2.25hp - 1617 motor (3.5in diameter) - Please make verbal or email request for this model.
• Hitachi 2.25 HP - No longer available thru K2.
• Makita 2.25 HP - No longer available thru K2.
• Colombo Spindle - Now Available. Ask a rep for details.
• HSD - Now Available. Ask a rep for details.

• Porter Cable 690LR or 892 router (should fit most routers with 3.5" round body)
• Porter Cable PC-7518 router 4.20inches in diameter.
• NEW* Bosch - 1617 motor (3.5in diameter)
• Hitachi (3.27 in diameter). Mount is available
• Makita (3.22 in diameter). Mount is available
• Makita (3.22 in diameter). Mount is available
• Colombo Spindle - Now Available. Ask a rep for details.
• HSD - Now Available. Ask a rep for details.

• Collects dust
• Fits 2.25" diameter hose.
• Vacuum and Hoses are NOT included
• Collects approximately 80% of cut debris

• Neatly confides motor , limit switches, and encoder wires out of the way.
• Igus design allows more wires to be added if needed by a snap through method.
• Additional room for extension cord.

• T-Slot Aluminum Table top size: 48" x 24" x .75" - T-Slotted.
• 6" sectional.
• Slots are 2" apart.
• Designed to fit 1/4-20 Nuts or hex bolt head.

• Welded mild steel (3 x 1.5 square tubing)
• Painted Gray
• Adjustments on feet

• 3 to 4 Servo Motors with feedback encoders.
• Geckodrive G320 servo controller
• Close Loop
• Wired for Step/Dir signals from Printer/Parallel Port
• Fully enclosed control box and pre wired for Parallel Interface
• 110 (std.) or 220 (request) watts power supply. 24VDC unregulated (~30V) 8 Amps.
• 5 watt power input wire from 1 computer USB port.
• Enable button
• Power Cord
• E-Stop Button
• Relay output ON/OFF controlled by software and G-Code. (Requires relay hardware.)
• HSD and COLOMBO are integrated into the control box.
• 1 extra Fuse
• No - Router E-Stop or remote off switch.
• Mach 3 Controller software CD with purchase or download demo from Mach 3 site.
• Mach 3 Set Up is from K2 CNC with purchase
• Support is from Mach 3 or MAch 3 via email or phone.
• 1000 count per revolution.

• Standard ABBA Rigid Rails
• Rolled
• Steel
• Grease fittings.
• Hi-Tolerance Ball screws of .001 backlash tolerance available( bearing house has a plastic dust cover )

• Vacuum Table - Not available thru K2
• A vise or Fixture to hold part - Not available thru K2
• Your Cutting Program - Not available thru K2
• Cutting Tool (End Mill or Drill Bit) - Not available thru K2

• Email (Unlimited)
• Phone (Limited to set up and assembly of machine and controller)
• Phone (basic operation of the machine. Not to include CAM programming)
• Controller support (Email from Mach 3)
• CAD/CAM Support (Email, Phone, Fax from Appropriate vender)
• On site support is available at an additional charge.

• Estimated time of 20-30 minutes from time of placing the machine on your table top.
• Wires pre-installed
• Connect plugs into the control box
• Connect Router to Extension Cord
• Connect plugs to computer

• 12 Month on all parts that are defective.
• 12 Month on all servo, gecko, controller.
• This does not cover dust, water, user damage

• Requires Palette Delivery
• Typical Company: UPS (United Parcel Services) Residential or Business. Delivery to the door.
• Palette is made of 1/2 thick ply wood, 2x2 and 2x4.
• $45 more for residence delivery
• A lift gate may be available upon request. Subject to availability.
• Total weight: 190LBS to 500 LBS.
• Shipping outside the US may need to have a different carrier and method.
• International Shipping is available.

• 15 days to return machine. Motors and controller can be used but not damaged. 100% Money Back on machine, motors, and controller less shipping and handling.

* Prices, features, and specifications are subject to change without notice.

Shipping price may vary, but is approximately $295 for this model for US delivery. Residence delivery is $45 more. Shipping outside of the US is available at additional charges. For outside of the US shipping, please provide a full address when requesting a quote.

Shipping container descriptions:
Typical Company: UPS Supply Chain Solutions (Freight company - NOT regular UPS) Wooden Palette weighs 190 lbs, customer will require a forklift. KG-2525 Requires very small assembly.